Wanted to go spec racing and have a car that was reliable and little between round maintenance. Wanted to buy one that was already done but all of the cars I looked at were too “used”. Figured that even a completely sorted car would need to have the engine and trans rebuilt. All the bushings and bearings would be suspect and it would probably need a new clutch. So I bought a very straight and well maintained (inch thick stack of dealer receipts) 1988 944. Stripped it to bare chassis. Before anything was put back on, it was either rebuilt or replaced with new. I am asking $10,000 ($9000 without the seat and accessories). It is a lot for one of these but I will bet that the cost of all the new items listed add up to more than the asking price. I don’t have the courage to do the addition myself. Essentially you are paying for all the items I bought and are getting the car and my labor for free.
Please feel free to email for more info.
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
If the photos don't show up please email me for them.
ENGINE:
Crank magnafluxed and polished
Rods magnafluxed and resized.
Head complete refresh by Lindsey Racing
Decked (minimum to achieve flatness)
3 angle seats / dress valves
New Turbo springs
New Glyco bearings
Oil pump blueprinted
Oil passages deburred and recontoured to promote flow to #2 main and away from #1
Pan has trap door mod
Oil pickup has ring mod
Canton 1.5 quart Accusump with solenoid actuator
Flywheel Magnafluxed and surfaced
New balance shaft bearings
All new seals and Victor Reinz gaskets
New water pump
New Cam and countershaft belts
New timing and countershaft idlers and tensioners
All new coolant hoses
New Rotor, Cap and NGK wires
MSD 6AL-2 Ignition (with 2 stage rev limiter again for rental use) with blaster coil and tach adapter
Injectors cleaned and matched by RC Injectors
Braided fuel line kit
Weltmeister Throttle cam
Lindsey Coolant vent kit
Lindsey A/C delete alternator bracket
Alternator has proper euro cooling cap and ducting.
TRANSMISSION
All new bearings and seals
Porsche limited slip unit
Urethane potted mount
Short 5th gear
FRONT SUSPENSION
Rebuilt lower arms with new ball joints
968 rear bushings
Koni adjustable shocks per 944 Spec rules
400 lb/in springs
Urethane sway bar bushings and links.
Urethane steering rack bushings.
New steering rack seals and boots
Power Steering fluid filter and cooler
Ground Control top mount camber / caster plates
Ground control shock tower brace (Integrated with C/C plates)
Calipers rebuilt
New Brembo rotors
Hawk DTC-70 pads
Lindsey brake cooling kit (Custom made to clear ABS)
REAR SUSPENSION
Prothane urethane torsion arm bushings
Prothane urethane torsion bar-mount bushings
Prothane rear trailing arm bushings
Weltmeister 30mm hollow torsion bar
Prothane sway bar bushings
Rebuilt Calipers
Hawk DTC-60 pads
New Zimmerman rear brake rotors
BODY
Custom cage with dual NASCAR bars, custom dash mounts
Window net
Interior safety net
Schroth 6 point HANS capable camlock harness (New September 2014)
Sparco Ergo seat (large) with removable side impact cushions
Sparco slider and seat brackets
New windshield
Stripped interior repainted original color with urethane paint
Custom dash and switch panels
3 pole electrical disconnect switch with alternator protection circuit.
Autometer 5” Tachometer
Autometer Pro comp Oil pressure gauge.
Billet camera mount
Gutted doors
Simplified wiring
Front tow hook
Eight 15 X 7 late offset phone dial wheels
Four Toyo 255 50 15 RA1s
SPARES
Starter
Alternator
2 doors
Door glass
Box of assorted relays and other electrical spares
Box of timing belt pulleys and hardware
Original passenger seat with 3 point factory harness.
There is not a bushing, bearing or seal that has not been replaced. The cage was custom built as was the dash / switch panel. I wanted a car that was versatile and reliable. I also had the insane idea that I might enter it in the 25 and possibly rent it. The wiring has been thinned out to get rid of all the unnecessary weight but still has everything needed for the factory gauge panel, headlights and wipers and ABS. While the ABS is not allowed for competition, it is still there for practice and for other drivers (rental). the seat is adjustable and there is a two stage rev limiter in addition to the one in the DME. The car is set up for instruction (I’m the HPDE Director for NASA NorthWest) so the cage is clear of the passenger seat and it also has NASCAR bars on both sides. The car is at a stage that allows it to be molded for its final configuration. Other than a fire extinguisher or fire system it is ready for its log book. I also considered the car for use as a rental which is why A lot of planning went into this project except for one thing. At 6’6” I am not comfortable in it. I have about ¼” headroom with a helmet. The list of features to follow is mostly complete but because of the sheer number of items there are bound to be some items omitted.